模型:IKPSF-125系列,en
筆記: Universal AC input/ Full range
High power density,High effiency and reliability
Output protections: OLP/OVP/SCP
Wide operating ambient temperature (-20℃~70℃)
Build-in remote sense function
All using 105℃long life electrolytic capacitors.
100% full load burn-in test
MODEL |
IKPSF-125-5,,nl,IKPSF-125-12,,nl,IKPSF-125-15,,nl,IKPSF-125-24,,nl,IKPSF-125-36,,nl,IKPSF-125-48,,nl,當前,,en,〜20A,,en,~10.5A,,ar,~8.4A,,ru,~5.2A,,ar,~3.5A,,ar,~2.6A,,bg,毫伏,,en,額定輸出電壓的±10%,,en,&GT = 17MS,,en,過沖和下衝,,en,電壓,,en,VDC〜370VDC,,en,頻率,,en,VAC PF,,en,VAC,,en,腐敗,,ha,A @ 230Vac 30A @ 115Vac冷啟動,,en,過流,,en,自動恢復,,en,OperatingambTemp,,en,GB4943-2011,,ar,mA。次級-PG,,en,;≤,,en,EMI傳導,,en,輻射,,en,符合EN55022,,en,CISPR22,,en,ClassB的,,en,EMS,,en,免疫,,en,ENV50204,輕工業水平,,en,criteriaA,,en,超過100,000小時,,en,×76×30.5毫米,,en,填料,,en,未特別提及的所有參數均在額定輸入下測量,,en,電源被視為將安裝到最終設備中的組件,,en,必須重新確認最終設備仍符合EMC指令,,en |
IKPSF-125-12 |
IKPSF-125-15 |
IKPSF-125-24 |
IKPSF-125-36 |
IKPSF-125-48 |
|
OUTPUT |
DC Output |
5V |
12V |
15V |
24V |
36V |
48V |
Rated Current |
20一個 |
10.5一個 |
8.4一個 |
5.2一個 |
3.5一個 |
2.6一個 |
|
CurrentRange Note 1 |
0~20A |
0~10.5A |
0~8.4A |
0~5.2A |
0~3.5A |
0~2.6A |
|
Ripple and Noise Note 2 |
100mV |
100mV |
100mV |
100 mV |
120 mV |
150 mV |
|
Voltage ADJ. Range |
±10% of rated output voltage |
||||||
Voltage Accuracy |
±2.0% |
±2.0% |
±2.0% |
±2.0% |
±2.0% |
±2.0% |
|
線路調整 |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
±0.5% |
|
負載調節 |
±2.0% |
±2.0% |
±2.0% |
±2.0% |
±2.0% |
±2.0% |
|
Set-up Time |
<=1200mS (230Vac input, Full load) <=2500mS (115Vac input, Full load) |
||||||
Hold up Time |
>=17mS(115/230Vac input, Full load) |
||||||
Temperature Coefficient |
±0.03%/℃ |
||||||
Overshootand Undershoot |
<5.0% |
||||||
INPUT |
VoltageRange |
90Vac~264Vac,127Vdc~370Vdc |
|||||
FrequencyRange |
47Hz–63Hz |
||||||
Power Factor(Typical) |
PF>0.98/115VAC PF>0.93/230VAC |
||||||
Efficiency ( Typical) |
82%/115Vac |
85%/115Vac |
85%/115Vac |
85%/20Vac |
86%/115Vacin |
86%/115Vac |
|
84%/230Vac |
87%/230Vac |
87%/230Vac |
87%/230Vac |
88%/230Vac |
88%/230Vac |
||
AC Current (最大。) |
1.5一個 |
1.5一個 |
1.5一個 |
1.5一個 |
1.5一個 |
1.5一個 |
|
Inrush Current (Typical) |
60A@230Vac 30A@115Vac Cold start |
||||||
Leakage Current |
<3.5mA |
||||||
PROTECTION |
Over Current |
105%~150% of rated output current, hiccup mode, auto recovery |
|||||
Over Voltage |
120%~150%的額定輸出電壓,,en,恆壓,,en,短路,,en,長期模式,,en,環境,,en,經營,,ca,溫度,,en,哼,,en,~90%RH無冷凝,,en,參考降額曲線,,en,儲存溫度,,en,℃〜85℃,,en,~95%RH無冷凝,,en,安全,,en,EMC,,en,安全標準,,en,UL60950-1,,en,ND,,en,埃德,,en,EN60950-1,,zh-CN,耐壓,,en,主次,,en,KVAC,,en,≤,,en,mA .Primary-PG,,en,毫安,,ar,二次PG,,en,KVDC,,en,隔離電阻,,en,≥,,en,M歐姆,,en,EMC排放,,en,符合EN55022,EN55024 ClassB標準,,en,諧波電流,,en,符合EN61000-3-2,-3,,en,EMC抗擾度,,en,符合EN61000-4-2,3,4,5,6,8,11,,en,EN55024,EN61000-6-2重工業水平,,en,其他,,en,MIL-HDBK-217F,,es,超過200,000小時,,en,L * W * H,,en,×51×28.8毫米,,en,冷卻方式,,en,注意,,en,未特別提及的所有參數均在230Vac輸入下測量,,en,額定負載和25℃的環境溫度,,en,通過使用端接有端子的12“雙絞線,在20MHz的帶寬下測量,,en,uF的,,en,uF並聯電容器,,en,hiccup mode |
||||||
Short Circuit |
Auto recovery |
||||||
ENVIRONMENT |
OperatingambTemp& Hum |
-20℃~70℃; 20%~90%RH No condensing |
|||||
Storage Temp. & Hum. |
-40℃~85℃; 10%~95%RH No condensing |
||||||
SAFETY &EMC Note 3 |
Safety Standards |
GB4943-2011; EN60950-1:2006 |
|||||
Withstand Voltage |
Primary-Secondary:3.0KVac;≤10mA .Primary-PG:1.5KVac;≤10mA .Secondary-PG:0.5KVDC;≤10mA . |
||||||
Isolation Resistance |
100M ohms |
||||||
EMI Conduction&Radiation |
Compliance to EN55022(CISPR22)ClassB |
||||||
Harmonic Current |
Compliance to EN61000-3-2,-3 |
||||||
EMSImmunity |
Compliance to EN61000-4-2,3,4,5,6,8,11;ENV50204,light industry level,criteriaA |
||||||
OTHERS |
MTBF (MIL-HDBK-217F) |
More than 100,000Hrs (25℃, Full load) |
|||||
Dimension (L*W*H) |
127×76×30.5mm |
||||||
Packing |
|||||||
Cooling method |
Cooling by free air convection |
||||||
NOTE |
1.All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature. 2.Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor. 3. The power supply is considered as a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. |